Browse Categories

Compound Gothic

 We just completed the design on this 24' wide X 14'6" tall for high snow loads. Fastest snow shedding greenhouses design.

We have made it easy for you to calculate the parts you need for your Compound Gothic.

EXAMPLE:  For instance if you want to build a 20x40 Compound Gothic .
 
Typically greenhouses are built with four feet (4 ft.) between each frame or hoop. Once you decide on your greenhouse length in this case 40 feet, then divide the length 40' by four 4' (hoop spacing) then add one (1, frame) the result in this case is 11 frames total, is the number of frames (hoops) you will need to build to construct a 20x40.Now we deduct the (2) end wall frames leaving us (9) interior hoop frames needed.

Start by selecting the end wall connector set below, this connector set builds both end hoop frames, so you only purchase one set of these. Next purchase nine  (9) of the interior connectors sets, one for each interior hoop frame needed. Next choose the model of hoop 12ft hoop bender you want and that it for building the frame set. Plastic can not be estimated on these units because the greenhouse sizes can vary a great deal in width height and length.


“The Connectors”

 

Below you will find the connector part listings to build one complete frame  complete frame. The two end frames are slightly different therefore we have listed them as a set for two end frames and a separate listing for the interior frames (between the two end frames). EXAMPLE if you require 10 frames for a 36 ft long greenhouse, then purchase one (1) set of the end wall frame connectors (this will build both (2) ends) then purchase eight (8) interior frame sets. These are connectors only!

“The Bender"

 

This hoop design requires a 12 ft bending tool listed below are several bender options all will produce this design so choose the one best suited for your budget. The only difference between the different 12 ft bender models below is the speed of production. The PF-12 commercial is just that its for bending a lot of hoops the DY-12 is slower but if your only bending a few hoops is a good choice.

 

 

We are the Original "Build Your Own Greenhouse People". Everyone else just follows and copies us.

 

Displaying products 1 - 6 of 6 results
DY-12 Hoop Bender
Price: $49.99
DY-12 Hoop Bender
Our DY-12 Series $54.99, High Tunnel Greenhouse Hoop Benders Frame Bending Tools were designed exclusively for the Homeowner Do it Yourself gardener.
unavailable
Compound Gothic End Frame Connector Set
Price: $62.99
Compound Gothic End Frame Connector Set
This connector set builds (2) end wall frames. Kit contains, 2 each 1 3/8" peak connectors, 4 each 1 3/8" multi-angle cross strut connector sets, 10 each 1 3/8" band clamps.
unavailable
Compound Gothic Interior Frame Connector Set
Price: $24.99
Compound Gothic Interior Frame Connector Set
This connector set builds both (1) interior Hoop/Frame. Kit contains, 1 each 1 3/8" peak connectors, 1 each 1 3/8" multi-angle cross strut connector set, 2 each 1 3/8" purlin clamps for side purlins.
C - 12 Hoop Bender
Price: $149.99
C - 12 Hoop Bender
Produces 12 ft wide Greenhouse Hoops using two-10' 6" lengths of 1 3/8 inch o.d. 16 or 17 gage chain link fence top rail tubing which is sold at all hardware stores. (center height is 6 1/2 feet +or-)
Vertical Mount Leg Set
Price: $149.99
Vertical Mount Leg Set
NEW! This Leg Adapter kit converts any of our EC-Series benders from the normally flat table mounted setup into the same vertical mount system used by our Commercial PF-Series benders. Leg Mount System only, the EC-Series Bending Heads are not included.
PF-12 Hoop Bender
Price: $449.99
PF-12 Hoop Bender
Shipping is free to all lower 48 States,, however UPS charges us a $80.00 over length surcharge on this item, this cost is added to your invoice during checkout. Commercial grade PF-12 Series Hoop Bender with leg stand.
free shipping
Shopping Cart
Your cart is empty.
Search
Products